Search

Aircraft Fueling and Defueling Procedures


Maintenance technicians are often asked to fuel or defuel aircraft. Fueling procedure can vary from aircraft to aircraft. Tanks may need to be fueled in a prescribed sequence to prevent structural damage to the airframe. The proper procedure should be confirmed before fueling an unfamiliar aircraft


Fueling

Always fuel aircraft outside, not in a hangar where fuel vapors may accumulate and increase the risk and severity of an accident. Generally, there are two types of fueling process: over-the-wing refueling and pressure refueling. Over-the-wing refueling is accomplished by opening the fuel tank cap on the upper surface of the wing or fuselage, if equipped with fuselage tanks. The fueling nozzle is carefully inserted into the fill opening and fuel is pumped into the tank. This process is similar to the process used to refuel an automobile gas tank. When finished, the cap is secured and subsequent tanks are opened and refilled until the aircraft has the desired fuel load onboard. Pressure refueling occurs at the bottom, front, or rear of the fuel tank. A pressure refueling nozzle locks onto the fueling port at the aircraft fueling station. Fuel is pumped into the aircraft through this secured and sealed connection. Gauges are monitored to ascertain when the tanks are properly loaded. An automatic shutoff system may be part of the aircraft system. It closes the fueling valve when the tanks are full. [Figure 1]

Figure 1. A float switch installed in a fuel tank can close the refueling valve when the tanks are full during pressure fueling of an aircraft. Other more sophisticated automatic shutoff systems exist

Precautions should be used with either type of fueling. First and foremost, it is absolutely essential that the correct fuel be put in the aircraft. The type of fuel to be used is placarded near the fill port on over-the-wing systems and at the fueling station on pressure refueled aircraft. If there is any question about which fuel to use, the pilot in command, other knowledgeable personnel, or the manufacturer’s maintenance/operations manual should be consulted before proceeding. Note that an over-the-wing refueling nozzle for turbine engine fuel should be too large to fit into the fill opening on an aircraft utilizing gasoline. Clean the area adjacent to the fill port when refueling over the wing. Ensure the fuel nozzle is also clean. Aviation fuel nozzles are equipped with static bonding wires that must be attached to the aircraft before the fuel cap is opened. [Figure 2] Open the cap only when ready to dispense the fuel. Insert the nozzle into the opening with care. The aircraft structure is much more delicate than the fuel nozzle, which could easily damage the aircraft. Do not insert the neck of the nozzle deeply enough to hit bottom. This could dent the tank, or the aircraft skin, if it is an integral tank. Exercise caution to avoid damage to the surface of the airframe by the heavy fuel hose. Lay the hose over your shoulder or use a refueling mat to protect the paint.

Figure 2. An AVGAS fueling nozzle with static bonding grounding wire When pressure refueling, the aircraft receptacle is part of a fueling valve assembly. When the fueling nozzle is properly connected and locked, a plunger unlocks the aircraft valve so fuel can be pumped through it. Normally, all tanks can be fueled from a single point. Valves in the aircraft fuel system are controlled at the fueling station to direct the fuel into the proper tank. [Figure 3] Ensure that the pressure developed by the refueling pump is correct for the aircraft before pumping fuel. Note that, while similar, pressure fueling panels and their operation are different on different aircraft. Refueling personnel should be guided through the correct use of each panel. Do not guess at how the panel and associated valves operate.

Figure 3. This panel at the pressure refueling station has valve position switches and quantity gauges to be used during refueling. Valve open position lights are adjacent to the switches for each tank When fueling from a fuel truck, precautions should be taken. If the truck is not in continuous service, all sumps should be drained before moving the truck, and the fuel should be visually inspected to be sure it is bright and clean. Turbine fuel should be allowed to settle for a few hours if the fuel truck tank has recently been filled or the truck has been jostled, such as when driven over a bumpy service road at the airport. Properly maneuver the fuel truck into position for refueling. The aircraft should be approached slowly. The truck should be parked parallel to the wings and in front of the fuselage if possible. Avoid backing toward the aircraft. Set the parking brake and chock the wheels. Connect a static bonding cable from the truck to the aircraft. This cable is typically stored on a reel mounted on the truck. There are other miscellaneous good practices that should be employed when refueling an aircraft. A ladder should be used if the refuel point is not accessible while standing on the ground. Climbing on an expensive aircraft to access the fueling ports is possible but does not give the stability of a ladder and may not be appreciated by the aircraft owner. If it is necessary to walk on the wings of the aircraft, do so only in designated areas, which are safe. Filler nozzles should be treated as the important tools that they are. They should not be dropped or dragged across the apron. Most have attached dust caps that should be removed only for the actual fueling process and then immediately replaced. Nozzles should be clean to avoid contamination of the fuel. They should not leak and should be repaired at the earliest sign of leak or malfunction. Keep the fueling nozzle in constant contact with the filler neck spout when fueling. Never leave the nozzle in the fill spout unattended. When fueling is complete, always double check the security of all fuel caps and ensure that bonding wires have been removed and stowed. Defueling

Removing the fuel contained in aircraft fuel tanks is sometimes required. This can occur for maintenance, inspection, or due to contamination. Occasionally, a change in flight plan may require defueling. Safety procedures for defueling are the same as those for fueling. Always defuel outside. Fire extinguishers should be on hand. Bonding cables should be attached to guard against static electricity buildup. Defueling should be performed by experienced personnel, and inexperienced personnel must be checked out before doing so without assistance. Remember that there may be a sequence in defueling an aircraft’s fuel tanks just as there is when fueling to avoid structural damage. Consult the manufacturer’s maintenance/operations manual(s) if in doubt. Pressure fueled aircraft normally defuel through the pressure fueling port. The aircraft’s in-tank boost pumps can be used to pump the fuel out. The pump on a fuel truck can also be used to draw fuel out. These tanks can also be drained through the tank sump drains, but the large size of the tanks usually makes this impractical. Aircraft fueled over the wing are normally drained through the tank sump drains. Follow the manufacturer’s procedure for defueling the aircraft. What to do with the fuel coming out of a tank depends on a few factors. First, if the tank is being drained due to fuel contamination or suspected contamination, it should not be mixed with any other fuel. It should be stored in a separate container from good fuel, treated if possible, or disposed of properly. Take measures to ensure that contaminated fuel is never placed onboard an aircraft or mixed with good fuel. Second, the manufacturer may have requirements for good fuel that has been defueled from an aircraft, specifying whether it can be reused and the type of storage container in which it must be stored. Above all, fuel removed from an aircraft must not be mixed with any other type of fuel. Good fuel removed from an aircraft must be handled with all precautions used when handling any fuel. It must only be put into clean tanks and efforts must be made to keep it clean. It may be put back in the aircraft or another aircraft if the manufacturer allows. Large aircraft can often transfer fuel from a tank requiring maintenance to another tank to avoid the defueling process. OR

Aircraft refueling is one of serious task carried out by trained aircraft mechanics.Refueling an aircraft is a process where trained personnel carried out task to fill an aircraft with fuel in order to enable the aircraft to continue its journey.

Generally there two methods of refueling which are

  1. gravity refueling

  2. pressure refueling.

Usually, pressure refueling is used when it comes to the refueling of large aircraft such as Boeing 747 and gravity fueling is used on small aircraft such as Cessna 172. This essay will describe process of pressure refueling and there are several steps and precautions that must be done by responsible personnel.


SAFETY PRECAUTIONS

  • The first precaution that must be done by trained personnel before carrying out the refueling process is to refer to the specific Aircraft Maintenance Manual.

  • Next, this operation must be carried out outside the hangar and should be in a well-ventilated area only.

  • Make sure there are fire extinguishers nearby. Get to know the location and serviceability of the fire extinguisher.

  • know the location of the emergency fuel shut off valve if its available.

  • This operation should be conducted by personnel who has the required knowledge. Do not operate any electrical and radio equipment in this operation. while refueling, do not connect the external ground power if its not connected before. And do not disconnect the ground power if its not connected before refueling.

  • do not operate of shutdown APU when refueling is being done.

  • After that, park the fuel tanker obliquely so that it can be driven away from aircraft in forward direction in case of emergency.

  • check the correct grade of fuel is used.

  • Also, ensure there is a proper bonding and groundings between aircraft and tanker, aircraft and ground, tanker and ground, and nozzle and filler port.

  • Do not smoke and no use of naked flame or equipment that can cause spark and ignite fuel. This operation should be conducted away from any source of fire and if there is an operation that involve with fire, it must be located 15 meters.

  • Finally, warning sign should be displayed and posted 15 meters from the location of operation.

do not refuel if

  • the aircraft Engines are running.

  • if you notice electrical storming.

  • if oxygen servicing is being perform in the aircraft.

  • if any part of the aircraft is over hot.

AIRCRAFT REFUELING PROCEDURE

  • There are several steps of aircraft refueling and it starts with the grounding of aircraft and the fuel tanker. Do not drag the hose along the leading edge.

  • Next, connect the fueling nozzle grounding cable to the aircraft grounding receptacle and immediately remove the filler cap. After that, insert the fuel nozzle into filler cap and commence fueling which is carried out by the suction method which is provided by the tanker.

  • Stop fueling once the desired fuel quantity has been reached. This can be monitor from the cockpit gauge reading.

  • Once fueling process is done, install and secure the filler cap.

  • Remove the fueling nozzle grounding cable from the aircraft grounding receptacle, the fuel tanker from the aircraft and grounding cable from the aircraft as well as from the tanker.

  • Finally, ensure the fuel does not come in contact with skin, clothes and eyes. Immediately clean and wash with water and special soap if this happens and also seek for the medical attention. If there is any spillage of fuel on the ground, clean the spillage

Fire Hazards When Fueling or Defueling Due to the combustible nature of AVGAS and turbine engine fuel, the potential for fire while fueling and defueling aircraft must be addressed. Always fuel and defuel outside, not in a hangar that serves as an enclosed area for vapors to build up to a combustible level. Clothing worn by refueling personnel should not promote static electricity buildup. Synthetics, such as nylon, should be avoided. Cotton has proved to be safe for fuel handling attire. As previously mentioned, the most controllable of the three ingredients required for fire is the source of ignition. It is absolutely necessary to prevent a source of ignition anywhere near the aircraft during fueling or refueling. Any open flame, such as a lit cigarette, must be extinguished. Operation of any electrical devices must be avoided. Radio and radar use is prohibited. It is important to note that fuel vapors proliferate well beyond the actual fuel tank opening and a simple spark, even one caused by static electricity, could be enough for ignition. Any potential for sparks must be nullified. Spilled fuel poses an additional fire hazard. A thin layer of fuel vaporizes quickly. Small spills should be wiped up immediately. Larger spills can be flooded with water to dissipate the fuel and the potential for ignition. Do not sweep fuel that has spilled onto the ramp. Class B fire extinguishers need to be charged and accessible nearby during the fueling and defueling processes. Fueling personnel must know exactly where they are and how to use them. In case of an emergency, the fuel truck, if used, may need to be quickly driven away from the area. For this reason alone, it should be positioned correctly on the ramp relative to the aircraft.

83 views

© 2019 by www.amequestionpaper.in.             All Rights Reserved.

  • Instagram
  • Facebook

WEBSITE TOTAL VISITOR